![]() Be sure that correct base and rings are being used in the correct orientation, and that the base screws and rings are tight. Many times, problems thought to be with the scope are actually mount problems. If possible, avoid exposing your Vortex riflescope to direct sunlight or any very hot location for long periods of time. Disassembling of riflescope may void warranty. Note: Other than to remove the turret caps, do not attempt to disassemble any components of the riflescope. Using your breath, or a very small amount of water or pure alcohol, can help remove stubborn things like dried water spots.Īll components of the Vortex Crossfire II riflescopes are permanently lubricated, so no additional lubricant should be applied.Be sure to blow away any dust or grit on the lenses prior to wiping the surfaces.When cleaning the lenses, be sure to use products, such as the Vortex Fog Free cleaning products or Lens Pen, that are specifically designed for use on coated optical lenses. The exterior of the scope may be cleaned by wiping with a soft, dry cloth. The fully waterproof and fogproof Vortex Crossfire II riflescope requires very little routine maintenance other than periodically cleaning the exterior lenses. Vortex Crossfire II 1-4x24 Maintenance Cleaning Need help with zeroing your riflescope? Watch the video below. This procedure can be repeated as many times as necessary to achieve a perfect zero. Carefully fire another three-shot group and see if the bullet group is centered on the bulls eye.Note: If the rifle is very solidly mounted and cannot be moved, simply look through the scope and adjust the reticle until it is centered on the fired group. Next, adjust the reticle to match the approximate center of the shot group (see section on Windage and Elevation Adjustment).Following all safe shooting practices, fire a three-shot group as precisely as possible.If scope is equipped, set the parallax adjustment to match the distance being used for sight-in: 100 yards is the most common zero distance, although a 200 yard zero may be preferred for long range applications.īe sure the reticle is in focus (see Reticle Focus). Sight in and zero the riflescope at the preferred distance. Vortex Crossfire II 1-4x24 Final Range Sight-InĪfter the riflescope has been bore-sighted, final sight-in should be done at the range using the exact ammunition expected to be used while shooting. To help you level the reticle - check out this tool! After aligning the reticle, tighten and torque the ring screws down per the manufacturer’s instructions.Use of bubble levels, a reticle leveling tool, a weight hung on a rope, or a flat feeler gauge will help with this procedure. Without disturbing the front-back placement, rotate the riflescope until the vertical crosshair exactly matches the vertical axis of the rifle.While viewing through the riflescope in a normal shooting position, slowly slide the riflescope back towards the shooter’s face-paying attention to the field of view.Slide the riflescope as far forward as possible in the rings.Set the riflescope to the middle of its magnification range.Before tightening the scope ring screws, adjust scope position for maximum eye relief to avoid injury from recoil. A low mounting will help assure proper cheek weld, aid in establishing a solid shooting position, and promote fast target acquisition.īegin with riflescope loosely installed in rings on the rifle. Use the lowest ring height that will provide complete clearance of scope and rifle-avoiding any contact with barrel, receiver, bolt handle or any other part of the rifle. ![]() Your new Vortex Crossfire II riflescope will require 30 mm rings. Mount an appropriate base and matching rings to your rifle according to the manufacturer’s instructions. Vortex Crossfire II 1-4x24 Rings and Bases How to adjust windage and elevation settings Each audible click moves the bullet’s point of impact 1/2 of a minute of angle (MOA).ġ/2 MOA closely corresponds to 1/2 inch at 100 yards, 1 inch at 200 yards, 1 1/2 inch at 300 yards.taking two (2) clicks to move the bullet’s point-of-impact approximately one inch at 100 yards. The Crossfire II riflescope incorporates adjustable elevation and windage dials with audible clicks. However, because your eyesight may change over time, you should re-check this adjustment periodically. Once this adjustment is complete, it will not be necessary to re-focus every time you use the riflescope. Note: Try to make this particular adjustment quickly, as the eye will try to compensate for an out-of-focus reticle.Turn the eyepiece focus knob in or out until the reticle image is as crisp as possible.Look through the riflescope at a blank white wall or up at the sky.Vortex Crossfire II riflescopes use a fast focus eyepiece designed to quickly and easily adjust the focus on the riflescope’s reticle. Vortex Crossfire II 1-4x24 Riflescope Adjustments Reticle Focus
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |